1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test . Integrated Circuit. Transistor Transistor Logic (TTL). 4−Line−to−16−Line Decoder /Demultiplexer. 24−Lead DIP Type Package. Description: The NTE is a. datasheet, circuit, data sheet: NSC – 4-Line to Line Decoders/Demultiplexers,alldatasheet, datasheet, Datasheet search site for.

Author: Dotilar Dilmaran
Country: Iceland
Language: English (Spanish)
Genre: Sex
Published (Last): 7 April 2015
Pages: 186
PDF File Size: 5.92 Mb
ePub File Size: 12.77 Mb
ISBN: 325-4-52232-168-4
Downloads: 83338
Price: Free* [*Free Regsitration Required]
Uploader: Mazudal

The filter also incorporates notches at and Hz, providing excellent dial tone rejection.

(PDF) 74154 Datasheet download

However, due to the internal structure of theonly one output can be enabled at a time. Your local phone i. Local control section contains a telephone interface circuit, ring detector circuit, signal decoder circuit, device status check circuit, device controlling circuit, device status feedback circuit. IC BCD – seven segment decoder.

So they are inverted a explained in the theory. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

When control signal is at high state, the outputs are nothing but the data present at its input terminals. Then respective LED glows.

National Semiconductor

So dztasheet output will be available at the output terminal. But when we try to implement a demultiplexer using a TTLthis is the truth table that is given in the book:. The amplitudes of the two sine waves should be such that.


With an astable operation, the frequency and pulse width are produced by two external resistors and one capacitor connected between Vcc-Discharge RDischarge-Threshold Rand Threshold-Ground C.

Here this circuit is designed for a period of 60 seconds. These demultiplexers are ideally suited for implementing high-performance memory decoders. To perform any operations through remote phone line, the user needs to dial to the local telephone to which the interfacing circuit is connected then the respective code of the device is dialed.

This circuit consists of some passive components like resisters, capacitors. The datasheet of these components is always the key to the correct implementation. Some technologies like IR remote control are used for short distance applications. By using this system we can control the light from a control room or by the cell phone of the marketing person.

National Semiconductor – datasheet pdf

Email Required, but never shown. The frequencies are chosen such that they are not the harmonics of each other. These tones are used for communication signaling. This device saves your money. Because of this here we need a BCD to seven segment decoder which gives logic low output for the respective BCD input. The DTMF mode is shortly called as tone dialing mode. If the device is already in the ON state, then we will here a beep sound.

The internal clock circuit is completed with the addition of a standard 3. On the M- models, this pin is tied to ground dayasheet low. Here this system works on tone dialing mode. Pressing digit 8 will produce the tone taken from tones Hz and Hz.


And that’s what is going on with the Above figure shows a single D-flip-flop. When this key is pressed the output of the line decoder goes low.

If the device is already switched ON then you will hear a short duration beep tone from beep tone generator unit. These flip-flops are used to latch the data that present at its input terminal click here to download datasheet. Yes here is the solution. Here it is wired as an astable multivibrater with a few external components like resister and capacitor are required along with the timer chip set.

datasheef When the datasheeet LED glows, the light falls on the emitter-collector junction the transistor. Now we follow the steps to test the proper switching of devices given below: Here we use the transistors to energize the relay coil.

Here this D flip flop is used in the toggle mode. This is achieved by using a 5V regulated power supply from a voltage regulated IC Control unit is kept with a sufficient backup.

4 Line to 16 Line Demultiplexer / Decoder

The person from a remote section is only to press the extension number to get connected to the respective number. Sign up using Facebook. Here it does not require any such operator to operate this exchange. The frequency table is as follows: Each filter output is followed by a single-order switched capacitor section that smoothes the signals prior to limiting.

It has 10 pins.

Start the discussion

Leave a Reply

Your email address will not be published. Required fields are marked *